Lowyat.NET: Latest topics in The Fast & The Furious

Passo Sette @ Alza, Modellista & admiration Style Bodykit

jenny91 — Tue, 24 Nov 2009 15:16:51 +0800

Source : http://www.myalza.com/phpbb3/viewtopic.php?f=13&t=42

Plate number VVIP tag, Police/JPJ/MPPP badges for car

freestyler_jg — Tue, 24 Nov 2009 13:13:56 +0800

As we all can see there is some cars on the road (especially luxury cars), there are always a beautiful VVIP tag besides their plate number, some ppl says police/JPJ/MPPP won't issue any summons to these cars, as they legally paid for their "VVIP membership", heard that Bukit Aman can apply those stuffs, wonder that howmuch it cost and how the application goes..?

Perodua official email, problem with Myvi EWP

Togepy — Tue, 24 Nov 2009 12:50:16 +0800

Hi, anyone have the perodua official email that i can check or complain to?
i've got some problem with my extended warranty program for my myvi. I did not get the cert for ewp and after i called them to check, they sent me 1 pdf file in black and white consisting the ewp information. In the pdf file that they sent to me, it only stated that my extended warranty is only 1 year/75,000km which is worth RM195 but in my ewp form, it is 2+3 years which worth RM390.
so now, i would like to email them the scan copy of the form to confirm but the contact form in their official website do not allow me to attach the files.

Anyone have the official perodua email that i could contact with for my problem??
lastly, anyone faced the same problem with me before??

NAZA KIA Rondo, How is this MPV

leongwk15 — Tue, 24 Nov 2009 11:35:28 +0800

Hi Guys,

I went to NAZA to view the Forte but found Rondo to be a good MPV (which really can sits 7 adults).

I would like to ask the Sifu here for advice and comment;

1) Rondo was launched last year and its almost 1 year already. How reliable is Rondo?
2) How is the Fuel consumption?
3) How is the power?
4) How is the Noise Vabrition Harhness (NVH) ?
5) How is NAZA service?
6) Any major problem?
7) IS there any special discount offer currently?

Thank you.

(WTA) can i renew r/tax & insurans for 6month only, juz want to know..thnks

li_hat — Tue, 24 Nov 2009 11:25:51 +0800

hi all forumers

i wanna asking if posible to renew the insurans and roadtax for 6month period only. Usually we renew it for 1 year.

thnks for those who give me the answers..

burst tyre, happen when travelling @ 110km/h

shadow111 — Tue, 24 Nov 2009 10:19:58 +0800

Hi All,

Was travelling at North South highway @ 110km/h when my tyre burst.
Below is the picture of my burst tyre. Was this burst serious?

Car Thief's Favourite,

LeoLilieno — Tue, 24 Nov 2009 09:03:25 +0800

I have read a lot of news recently about car being stolen or even being robbed. As I am getting my car real soon, I am very worried about the fact that thieves are getting more daring and high tech in stealing car. So, which car brand and model are thieves' favourite and any suggestion in preventing our toy from stolen? By the way, my toy is Toyota Camry 2.4v.

Toyota VIOS Face Lift, Did anyone know about this?

leongwk15 — Tue, 24 Nov 2009 08:10:33 +0800

Hi guys,

Just heard from the Toyota SA that next year VIOS will have a facelift.

I have checked the Thailand Toyota but seems to be no facelift yet. Usually it will appear 1st in Thailand

Do you guys know bout this and care to share? Spyshots?

Kereta Bikin China, 56k kenot, pic heavy

ericmaxman — Tue, 24 Nov 2009 03:24:09 +0800

For most of us, the words "Made In China" can easily be deduced as garbage. Yeah, god damn low NCAP ratings aside, I do sincerely believe that China cars are almost or even on par with what Proton has achieved.

Forget the earlier copycats, I think this is more like it.

Changfeng (Guangzhou Auto's subsidiary) Acuman hatchback to go on sale next year.

Silicon wiper blades, How good are they?

Banzai_san — Tue, 24 Nov 2009 03:10:28 +0800

Hi,

I am interested in getting the silicon blade wiper, but I am not sure if they are really good.
They are advertised as being long lasting compared to the normal rubber blade wipers..

Do the silicon blades perform (in terms of windscreen clarity in rain) better than the normal/natural rubber wiper blades?
What other advantages of the silicon blade wipers?
Are there any complaints, comments, disadvantages (apart from the high price compared to normal rubber wiper) of the silicon blade wiper?

Anyone care to share their experience?

Thanks.

Perodua Launch @ KLCC Scene, Alza club

jenny91 — Tue, 24 Nov 2009 02:18:02 +0800

[WTA] Flushing my radiator, Wira 4g15 Radiator

adrianteddy — Tue, 24 Nov 2009 02:06:47 +0800

Sifu, just notice my radiator where u open the metal cap in the middle. when open inside got a lot of rust. what can i do? can i flush it to make the rust come out? i think for 14 years, the radiator didnt being clean before. Sifu please guide me step by step on how to flush it and after flush , what should i add into the radiator? izzit just water or the green radiator coolant fluid?

WTA - about perodua service centre,

ongdandy — Tue, 24 Nov 2009 02:04:42 +0800

anyone know where i can find perodua service centre around subang jaya, kelana jaya, sunway area?

vios, full spec

ddongusa90 — Tue, 24 Nov 2009 00:03:23 +0800

1. Brand. toyota
2. Budget.80k
3. New/Used/Unreg. new or used
4. Specs. s spec
5. Transmission.AT SHIFTRONIC
6. NA or FI ?
7. Type. sedan
8. Remarks.

my kelisa 1.0 AT, vibrate and noise

ongdandy — Mon, 23 Nov 2009 22:40:54 +0800

hi guys.. i just come back from subang..and my car vibrate when i stop at the traffic light while the gear still in D mode. and when i step on the gas pedal.. i hear some noises from the bottom.. like kah tak kah tak. is it from the gear mounting?

Need help for my Honda CRV speed meter...., who can help??

street5537 — Mon, 23 Nov 2009 20:07:13 +0800

few day before i use gp change my alarm system, then after tat my car speed meter r not running and also the oil meter r not stable.....

any1 can gv me some suggestion to solve the problem..... pls help...

Nissan latio sport, manufacturer 2009 or 2010?

~Guyver~ — Mon, 23 Nov 2009 18:56:16 +0800

As title above, i have ordered latio sport recently, juz wanna ask all sifu comment. Should i take 2009 stock wit 4k rebate or wait until 2010 stock. If 2009, i can get the car around 2nd week of December, for 2010 stock, i gonna wait until feb or march and the discount price might b change from 4k to 2k.

perodua alza, come n share yr tought :)

architture — Mon, 23 Nov 2009 18:06:04 +0800

hi boss,

perodua jus launch new mpv called ALZA.

wat do u think ???

for me, i think better outlook than exora.

price wise not much diff

http://paultan.org/2009/11/23/video-perodu...-tv-commercial/

The CamberNut Myth by Tire shops, is it a right job or con job ? discussio

BridgestoneRE711 — Mon, 23 Nov 2009 17:08:41 +0800

actually i am very against the cahnge of the camber nut, it's like very single shop which i have been to will ask me to change the camber nut and adjust it.
Finally, in the end i have to change one because the angle lari too much, i knew it will lari becasue 1 thing, i hit the pot-hole which damaged my tire, and when it was on the tow truck platform, it was forced scratched to the side kerb.

the shop did show me the original proton gen2 camber, front camber. it really doesn't look like something that can be adjusted. it is located at the lower arm of the absorber mounting.

any ideas where ?

++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
http://www.stockcarracing.com/tipstricks/c...etup/index.html
In the world of race car setup, the frontend settings can become downright confusing. But theres much to gain by understanding caster, camber and toe settings, and how they can work together to make your race car go faster.

Caster

A side view of the car shows an imaginary line runs through the center of the upper ball joint to the center of the lower ball joint. This is known as the pivot line. If this line is absolutely vertical, then the caster measurement is zero, or no caster. When the top of this line is leaned toward the rear of the car, we now have positive caster.

Try pushing around a chair with casters on it. You will find it has no directional stability. This is because the casters have negative caster and want to follow the slightest force in any direction. Your race car should have

positive caster to achieve that directional feel.

As opposed to some years ago, most race cars now have power steering. This allows the use of more caster.

In cars using stock or near-stock frontend geometry, caster can be increased from the factory settings. Caster stagger is also a useful setting. Caster stagger occurs when there is more positive caster on the right side than on the left. When entering a turn to the left, the excess caster on the right will give the car a natural tendency to turn left.

Long tracks, especially the paved ones, need only a small amount of caster staggerperhaps only 1 degree. At a ¼-mile dirt bullring, much more can be an advantage. The IMCA stock car we recently put together in Stock Car Racing uses 9 degrees of caster on the right and 5 degrees on the left. This is a lot, but the car turns in easily.

Setting caster is easily done with a gauge built for that purpose. Most of the store-bought units screw on or magnetize to the front hub. Turn plates are then placed under the front wheels. The wheels are steered a certain number of degrees each way. The gauge will then read the caster in degrees. This type of gauge may be necessary with aftermarket rod ends.

We have constructed a simple gauge for use with stock ball joints. Each gauge will fit only the type of car it was made for. Notice each ball joint has some threads sticking out past the nut. Find a piece of tubing that will fit snugly over the ends of the ball joint tang. Measure the distance between the nuts on the top and bottom. Cut the tubing about 1/16-inch shorter. On one end, notch the tubing ½ inch down and halfway across. This will leave a half-round notch. Weld a 15-inch rod at a 90 degree angle to the tube on the notched side. The tube should be 11 inches from the end of the rod. After welding, make sure the rod is at a 90-degree angle to the tube.

Now place the tube over the bottom ball joint threads. The notch will allow the inside of the tube to rest against the upper threads. Place an angle finder on the rod and directly read caster.

Lots of caster stagger is ideal on a small dirt track. Get all the caster the right side will allow with the correct amount of camber. Then adjust the left-side caster using enough caster stagger to give you the feel you want entering a turn. Start with a lot and then take it out if you dont like it.

Camber

Another setting for the front suspension is camber. Camber is measured at the wheel, not the ball joints. A frontal view of the car, when the wheel is straight up (no lean), shows the wheel has no camber. When the wheel is leaned in at the top toward the center of the car, it has negative camber. Therefore, when it leans out at the top, the wheel has positive camber. Race cars can use both positive and negative camber settings to their advantage.

Camber is a very visible part of the frontend settings. We have all seen the right front leaning toward the center of the car. Sometimes this is severe enough that the outside of the tread is not touching the ground. This much negative camber reduces the traction at the front of the car. If the car seems balanced in its handling with this setup, then the suspension is crippled somewhere else.

Only the right amount of camber will net maximum traction. Selecting the right amount is determined by the built-in suspension design. All the suspensions we deal with have camber gain. When the wheel goes up in relation to the chassis, which is called bump travel, the camber increases, or gains. Camber is designed to reduce the effect of tire flex. Camber gain also adjusts for suspension movement. Together, they work to keep the tread surface flat on the track. The big question is how much do you need.

The tire needs about 1 degree to start with. With most suspensions discussed here, there will be a gain of 1½ degrees to 2 degrees per inch of bump travel. If your suspension has 3 inches of bump travel, that would add up to 4½ degrees to 6 degrees. Add in the 1 degree negative initial setting and you have 5½ to 7 degrees negative at full travel.

This is best accomplished by blocking the chassis and removing the spring. Then the suspension can be cycled with a jack. Set the camber at full bump travel. The car should be level. Then with the spring replaced and the car on its wheels, measure the camber. From now on that will be your static camber setting on the right front.

A problem with some stock suspension mountings is not allowing all the caster needed while providing enough camber. Split the settings, if necessary, by removing a degree of caster and a degree of camber. Just keep the caster stagger the same.

Camber on the left front will not be the same as on the right. You will need positive camber on the left front wheel. There is little camber change as the left front goes down, the reverse of bump travel. Therefore, an initial setting of ½ to 1 degree positive camber will work well.

Camber can be set using store-bought gauges or with the homemade caster gauge described above. Earlier the rod was cut to 15 inches. This length allows you to fit the rod to the wheel and use the angle finder to measure the camber. An angle finder with a magnetic attachment definitely makes reading easier.

Toe Setting

When setting up the car, its often not desirable to have the front wheels exactly parallel to each other. Some situations call for toe-out while others call for toe-in, thus the term toe setting.

The toe setting will vary with the type of track and the steering linkage. Long tracks and/or paved tracks may require toe-in at times. Most of our cars with stock-type steering linkages running the small dirt tracks will need a bit of toe-out to work properly. This is not a case of if somes good then mores better. A toe-out of ¼ inch to 3/8 inch is about right for most. Too much adds drag. Too little will give the car an unstable feeling.

Toe is best measured some other way than hooking a steel tape in the tire tread on one side and going to the other side. The tire tread is notoriously less than straight on the tire carcass. When two people hold a tape across the tires, it is very difficult to keep the measured points the same distance from the ground. When the measuring points are not the same height on the tire, the distance between them changes. Instant error.

Toe boards are available that have saw slots in which to hook two steel tapes. These lay against the tire on each side of the car. They work OK when the tire has no bulges or raised letters.

We have made toe setting tools which key off the wheel. They may be more accurate as long as the wheel is straight. They are made of 3/8-inch steel rod and welded together. The top crosspiece is 10 inches long, the center bar is 15 inches and the long bottom bar is 28 inches. There is no slot to hang the tape, just line it up with an edge. This aids accuracy by not letting a pull on the tape move the tool.

Lay two steel tapes next to the ends of the bottom rods. Make sure each reads the same on the hook end. Read the toe-in/out on the other.

Supercars & Exotics 5,

anType — Mon, 23 Nov 2009 15:36:13 +0800

Continued from V4.

Same rules still apply:
Supercars & high-end sports cars (Ferrari, Lamborghini, high-end Porsche - Turbo, GT2, GT3, etc)
High-end continental luxury cars (Rolls-Royce, Bentley, etc)

Mercedes-Benz AMG series, BMW M series, are also suitable.